Did your garbage disposal start making strange gurgling sounds and then suddenly stop working altogether? Or maybe you just moved into a new home and want to install a new disposal. Either way, you’re in the right place.
We’ll show you how garbage disposal installation can be quick and easy. All you need is some basic knowledge of home repairs and the right equipment.
You’ll also need a handy how-to guide, which you’ll find below. Take a look.
How to Install Your Insinkerator Garbage Disposal in 10 Easy Steps
Let’s roll up our sleeves and get started.
Step 1: Gather Your Supplies
Here’s what you’ll need:
- Dishwasher drain connector kit
- Phillips and flathead screwdrivers
- Hammer
- Pipe wrench
- Plumber’s putty
- Electrical connectors and clamps
- A bucket
Step 2: Disconnect the Power and Water
The first step is disconnecting the power, which you can do from the circuit breaker or the fuse box. Next, turn off the water supply via the shutoff valve under the sink.
Then, use the wrench to disconnect the pipes below the sink. Have your bucket handy to catch any water.
Once the pipes are gone, push on the drain from below the sink. It’ll come right out. Wipe the sink with a clean cloth.
Step 3: Install the New Garbage Disposal Drain
Your new drain, or flange, should come with a rubber gasket. However, you can choose to place a layer of plumber’s putty instead of the gasket.
We should mention that many believe putty makes for a better, long-lasting seal than the gasket. Anyway, whichever sealant you decide on, make sure you press down on the drain to set it in place.
Step 4: Secure the Mounting Bracket
For this next step, you’ll need to keep the garbage disposal drain in place as you work below the sink. Either ask someone to hold it in place for you or place something heavy on the drain, like the disposal itself. To protect the sink from scratches, lay a towel between it and whatever object you decide to go with.
Next, slide the fiber gasket onto the drain sleeve beneath the drain, followed by the backup flange. Finally, use your screwdriver to tighten the fastening, or mounting, screws to the mounting bracket.
The best way to do this is to turn each screw a couple of turns at a time, alternating between each one. This ensures that the bracket and drain are effectively seated against the sink.
Bear in mind that, once you’re done, you may find excess putty around the drain. That’s perfectly fine. Simply, cut off the extra pieces using a sharp knife and throw them away.
Step 5: Attach the Discharge Tube
Start by attaching the rubber gasket to the tailpipe. This is the large opening on the side of the garbage disposal.
Next, look for a piece of short pipe with a 90-degree angle, known as the discharge tube. Then, take the metal fastening flange and slide it through the tube.
After that, you’re going to take the flared end of this tube and attach it to the rubber gasket you just installed on the tailpipe. Secure the tube in place using the two screws provided. They’ll help form a watertight seal between the discharge tube and the tailpipe.
Step 6: Prepare the Dishwasher Drain Hose Outlet
Above the tailpipe, you’ll find a smaller outlet closed shut via a knockout plug where the dishwasher drain hose will go.
To remove it, lay the disposal on its side. Then, using a hammer and a screwdriver, gently tap on it until it pops out and into the garbage disposal.
If you don’t have a dishwasher, you can keep the knockout plug in place.
Step 7: Connect the Wires
Garbage disposals are either hardwired or corded. If the garbage disposal comes with a factory-installed cord, then you’ve got it easy. All you have to do is plug the cord into the outlet located underneath your sink.
If the unit is hardwired, you’ll need to do a bit of electrical work. You’ll also need to buy some electrical cable connectors and a power cord kit.
Here are the basic steps to set up your hardwired garbage disposal and connect it to a cord. Before you start, make sure the circuit breaker is turned off.
- Turn the garbage disposal on its side to remove the electrical cover plate on the bottom.
- Pull out the wires.
- Using wire connectors, join wires from the disposal to their corresponding wires coming from the power supply.
- Tighten the connectors and gently push the wires back into the body of the disposal.
- Replace the cover plate and secure the power cord to the bottom of the unit via a clamp.
Step 8: Hang the Garbage Disposal
This step is the most challenging for some people because the disposal can get pretty heavy as you’re working below the sink. However, if you’re doing the garbage disposal installation alone, remember that slow and steady wins the race. It also reduces the risk of damage or injuries.
First, make sure the mounting tabs align with the slide-up ramps on the mounting ring you screwed in place in step three. There are three in all to ensure maximum stability of the unit.
Start by holding the garbage disposal in one hand. With the other, turn the lower mounting ring. Keep rotating it until all three tabs lock into place on the mounting framework.
Step 9: Connect the Insinkerator Garbage Disposal Drain to the P-Trap
Remember the discharge tube you attached to the Insinkerator disposal in step four? You’re going to connect it to the pipe underneath the sink.
Next, insert the discharge tube and slide the clamp up over it. The tube should now be positioned within the threads on the coupler on the p-trap, also called the drain trap. Make sure you tighten the clamp to prevent leaking.
If the tube is too long, cut off the extra length. On the other hand, if it’s too short, you can always buy an extension. Simply attach one end of the discharge tube and the other to the drain trap.
Step 10: Test Your New Insinkerator Garbage Disposal
Remember to turn the electrical breaker and the water supply back on. Then, run the water to check for leaks. If everything looks good, plug in the disposal and test it out.
Conclusion
Garbage disposals are a convenient addition to any kitchen. If you’re into DIY projects, then our how-to guide on garbage disposal installation should come in handy.
Installing a garbage disposal is quite easy if you follow the manual. In some instances, it can be harder if you have to make a lot of adjustments to your drains. You might have to ask that a plumber comes over for this.
Once the garbage disposal has been installed, it should be possible to use it for several years. Just make sure that you don’t place the wrong items inside of them. Garbage disposals have blades and they can break if you place certain items in them.
Your drains can also get clogged if you place them in the garbage disposal. It can be a lot of work to get this removed and a plumber might have to use water pressure to fix it.
Garbage disposals need to be cleaned often to make sure that they smell nice. This takes some attention but is quite easy to do.
Just grab your tools, and you’re ready to go!
InSinkErator is a big brand and they offer a lot of customer support if you need it. Simply reach out to them.
Make sure that you follow the safety instructions when you install garbage disposal! You have to deal with water and electricity so read up about GFCI outlets.
https://insinkerator.emerson.com/en-gb/support/manuals-spec-sheets